LUFTooL Trap Condensation Piece SPIRO

When the exhausted air has to pass through an unheated zone, it is necessary to ensure that only a minimum of condensate forms in the duct and that it does not mold and water does not flow into the heat recovery unit. LUFTooL Trap condensation pieces will help with this. The combination with pipes made of EPE or EPS insulators is ideal due to minimal thermal bridges.  The plastic condensate piece or condensate outlet is inserted into the HVAC thermal insulation pipe (EPE or EPS). In EPE and EPS designs, we offer it for air ducts with an inner diameter in sizes from 125 to 200 mm. The condensation piece removes excess moisture from the pipe. By inserting the condensation piece into the insulating material pipe, thermal bridges of this part of the system are eliminated. The condensate drain hose d16 is fully compatible with the condensate piece, which is only pushed onto the drip elbow. The LUFTooL Trap condensation piece is suitable for exhaust pipes (EHA) - from the heat recovery unit to the exterior. In winter, air flows in this duct with almost 100% humidity when the moisture condensation in the recuperator. It is placed above the heat recovery unit in a vertical duct. Technical information: - Height: 10 cm - Not compatible with SPIRO, KG, etc. piping!! only with piping according to designation - Compatible with D16 condensate drain hose PETG material: Flexible and strong High impact resistance and durability Harmless material Low shrinkage as it cools 100% recyclable Assembly: Cut the pipe in the place where you want to place the condensation piece. Vertical piping at the heated boundary of the thermal envelope is ideal. Place a condensation piece on the bottom of the pipe and cut a hole for the plastic elbow as tightly as possible with a snap-off knife. Insert the condensation piece and fit the top parts of the pipe. Seal the joint airtight with aluminum tape and thermally secure with at least two layers of thermal tape. Connect the condensate drain hose to the elbow and connect it to the sewer through a flooded siphon (beware of freezing). Package includes: 1) Condensation piece Packed loose in a box.

LUFTooL Trap products are designed to collect condensed water on the inside of the pipe in the ventilation systems. They are usually installed on pipes that blow air from the interior through the unheated part of the house. The condensation piece drains condensate from the duct walls outside the duct. Our Condensing Pieces are: • very tight - designed to save space compared to other condensate collection solutions • equipped with a gutter elbow that is compatible with conventional condensate drainage hoses • made of PETG material, thus minimising the formation of thermal bridges • designed to be installed in vertical and horizontal pipes (horizontal pipes must always be in a gradient towards the drain) • efficient, depending on the flow rate and type of pipe material, they are able to collect up to 91% of condensed moisture • manufactured in three variants (for EPE, EPS and SPIRO pipes) Made of PETG material: • which is a flexible and strong material • has high impact resistance and durability • is made from health-safe materials • has low shrinkage on cooling • is 100% recyclable Package includes: Condensation piece, 2 sealing rings for the SPIRO version, manual. Packed in a box or foil

Replacement actuator for the Distribute system and the automatic damper module. The actuator can be easily replaced with a new one. After installation, do not forget to calibrate.

LUFTooL Trap products are designed to collect condensed water on the inside of the pipe in the ventilation systems. They are usually installed on pipes that blow air from the interior through the unheated part of the house. The condensation piece drains condensate from the duct walls outside the duct. Our Condensing Pieces are: • very tight - designed to save space compared to other condensate collection solutions • equipped with a gutter elbow that is compatible with conventional condensate drainage hoses • made of PETG material, thus minimising the formation of thermal bridges • designed to be installed in vertical and horizontal pipes (horizontal pipes must always be in a gradient towards the drain) • efficient, depending on the flow rate and type of pipe material, they are able to collect up to 91% of condensed moisture • manufactured in three variants (for EPE, EPS and SPIRO pipes) Made of PETG material: • which is a flexible and strong material • has high impact resistance and durability • is made from health-safe materials • has low shrinkage on cooling • is 100% recyclable Package includes: Condensation piece, 2 sealing rings for the SPIRO version, manual. Packed in a box or foil

Extension cable for LUFTooL damper modules with automatic control. It is used to extend the wires between the actuator and the control unit. It is equipped with an M-male connector on one side and an F-female connector on the other. Length 20, 40, 60 cm.

The SPIRO pipe connector with a diameter of 100 mm is a universal modular element from the LUFTooL Distribute series. It consists of components that can be quickly and tightly screwed together into various units. The LUFTooL Distribute system is: • an innovative system for distributing air flow into individual zones/rooms • modular (its components can be combined) • designed for flexible plastic pipes with a diameter of 75 and 90 mm and traditional SPIRO pipes of 100 mm • designed for ventilation in family houses and small businesses with air flows through individual branches up to 100 m3/h • a very tight system achieves class D tightness according to ČSN EN 15727 • suitable for the supply and exhaust of commonly polluted air (without chemicals, etc.) • fully cleanable, brushes can be pulled through the damper without dismantling the damper module • made of ABS and PETG The package contains: Plastic molding of the nozzle body (PETG), T-shaped sealing ring. Packed in a plastic bag. Dimensions: The nozzle can be screwed on one side, e.g. to: LUFTooL connectors (LF-CO-125) - which are inserted into the distribution box LUFTOMET® Flat boxes LUFTooL damper module with automatic or manual control Installation examples Mounting via connector or damper module to the distribution box Mounting Screw on the appropriate module. Then slide the pipe over the seal and secure with a self-tapping screw.

The automatic damper module is part of the LUFTooL Distribute series. The damper enables automatic control and, together with other elements of the modular system, is used for zoning ventilation with heat recovery in family houses, apartments and small businesses. The system can be used for both supply and exhaust air with flow rates up to 100 m3/h in one branch. The LUFTooL Distribute system is: • an innovative system for distributing air flow into individual zones/rooms • modular (its components can be combined) • designed for flexible plastic pipes with a diameter of 75 and 90 mm and traditional SPIRO pipes of 100 mm • designed for ventilation in family houses and small businesses with air flows through individual branches up to 100 m3/h • a very tight system achieves tightness class D according to ČSN EN 15727 • suitable for the supply and exhaust of commonly polluted air (without chemicals, etc.) • fully cleanable, brushes can be pulled through the damper without dismantling the damper module • made of ABS and PETG The package contains: A plastic molding of the damper body (ABS) fitted with a damper blade and damper axis (PETG). A calibrated servo drive is mounted on the module body in the closed position. Instructions. Unlike the illustration, the package does not contain a blue cover. Packed in a plastic bag. The damper module can be screwed on one side, e.g. to: LUFTooL connectors (LF-CO-125) - which are inserted into the distribution box LUFTOMET® Flat boxes On the other hand, the module is ready for connection to LUFTooL pipe sockets: LT-SP-75-F....LUFTooL Spigot pipe socket (75 mm, female) LT-SP-90-F....LUFTooL Spigot pipe socket (90 mm, female) LT-SP-100-F....LUFTooL Spigot pipe socket (100 mm, female) (spout for traditional SPIRO pipes, white plastic or flexible SONO, Mastersan, etc. pipes, dimension 100 mm) Installation examples 1) installation via the connector to the distribution box - regulates the air flow coming out of the distribution box 2) installation in front of the LUFTOMET Flat box - regulates the air flow before the outlet Characteristics servo drive Operating voltage: 4.8 - 6.0 V Gear material: metal (first gear from the motor plastic) Dimensions: 23 x 12 x 29 mm Standing torque: 1.8 kg/cm (4.8 V); 2.2 kg/cm (6.0 V) Temperature range: 10 to +50°C Weight: 13.5 grams Wire length: 175 mm Rotation tolerance: ± 8% Controlling the damper module To control the damper module, you can purchase the LUFTaTOR API12 control module - this is software and a control board that allows you to control up to 12 dampers using the HTTP REST API. !!! In the case of control by your own system, the servo drive is not guaranteed. Basic requirements for system operation: - max. air flow through one fully open damper is 100 m3/h. Depending on the position of the damper and the percentage of its closure, the maximum allowed flow rate (LFmax) is reduced proportionally. The air flow rate through one or more distribution boxes (PBmax) generated by the heat recovery unit in one direction (supply/exhaust) must not exceed the sum of the maximum flows of all dampers PBmax < ΣLFmax - air temperature flowing through the damper 10-40°C - air temperature around the actuator and control board 10-40°C, humidity 30-90% RH - it is always necessary to maintain access to the control board and actuators for possible replacement Service To clean the piping system, the damper blade can be easily removed through a conveniently located service opening from the distribution box. To remove the damper axis and the outer part with the actuator, it is necessary to remove two screws using a Phillips screwdriver. The damper body and the neck do not need to be removed.

The connector is part of the LUFTooL Distribute system, which is innovative and modular. The entire system is designed for easy air regulation, thanks to which it is possible to freely distribute the air flow in individual zones or rooms in family houses and smaller businesses. However, individual elements can also be used for other elements such as ceiling and wall boxes. For example, the connector can be installed in any box with an appropriate opening. The LUFTooL Distribute system is: • an innovative system for distributing air flow into individual zones/rooms • modular (its components can be combined) • designed for flexible plastic pipes with a diameter of 75 and 90 mm and traditional SPIRO pipes of 100 mm • designed for ventilation in family houses and small businesses with air flows through individual branches up to 100 m3/h • a very tight system achieves class D tightness according to ČSN EN 15727 • suitable for the supply and exhaust of commonly polluted air (without chemicals, etc.) • fully cleanable, pulling brushes through the damper can be done without dismantling the damper module • made of ABS and PETG Package includes: Connector (PETG), two sealing rings. Packed in a plastic bag. Assembly: E.g. to: LUFTooL damper module with automatic or manual control LUFTooL pipe sockets (75, 90 and 100 mm) Installation examples Installation via connector or damper module to distribution box